Results 1 to 16 of 16

Thread: Remove sticker adhesive from APX housing?

  1. #1
    triptolemus's Avatar
    triptolemus is offline T S - Moderator
    CS Forums $upporter
    Join Date
    Dec 15, 2012
    Posts
    872
    Thanks
    607
    Thanked 1,407 Times in 505 Posts
    Country: United States

    Default Remove sticker adhesive from APX housing?

    Does anyone have and tried and true methods for reliably removing left over sticker adhesive from the front of an APX without causing problems? Some knucklehead decided to place a round sticker directly over the speaker grille.

    I hate stickers and markings on shit.


  2. #2
    Join Date
    Aug 19, 2012
    Location
    FLORIDA/QUEBEC
    Posts
    477
    Thanks
    73
    Thanked 210 Times in 128 Posts
    Country: Canada

    Default

    Goo Gone. The orange stuff works great. GARY.

  3. The Following 4 Users Say Thank You to N4KVE For This Useful Post:

    Avery Johannssenn (Apr 18, 2018),com501 (Apr 15, 2018),motorola_otaku (Apr 16, 2018),triptolemus (Apr 15, 2018)

  4. #3
    com501's Avatar
    com501 is offline T S - Moderator
    CS Forums $upporter
    Join Date
    Jan 18, 2013
    Location
    In Your Network
    Posts
    2,348
    Thanks
    1,543
    Thanked 1,338 Times in 686 Posts
    Country: United States

    Default

    I second that - we use Goo Gone on our rental fleet.
    Retarded Mongoloid on PCP...

  5. The Following User Says Thank You to com501 For This Useful Post:

    triptolemus (Apr 15, 2018)

  6. #4
    triptolemus's Avatar
    triptolemus is offline T S - Moderator
    CS Forums $upporter
    Join Date
    Dec 15, 2012
    Posts
    872
    Thanks
    607
    Thanked 1,407 Times in 505 Posts
    Country: United States

    Default

    Thanks guys, will pick some up tomorrow morning.

  7. #5
    Join Date
    Jan 31, 2015
    Location
    Portland OR
    Posts
    588
    Thanks
    774
    Thanked 747 Times in 368 Posts
    Country: United States

    Default

    A third vote for Goo-Gone. I have not tried it on polycarbonate yet. Goo-Gone and Goof Off are great for graffiti. On radios, I alternate between alcohol and WD40. If one doesn't break down the adhesive, the other generally does.
    Bow wow wow yippie yo yippie yay

  8. The Following 2 Users Say Thank You to Bill_G For This Useful Post:

    Navy_BOFH (Apr 20, 2018),triptolemus (Apr 15, 2018)

  9. #6
    Join Date
    Apr 27, 2013
    Location
    Columbus Ohio
    Posts
    236
    Thanks
    338
    Thanked 189 Times in 96 Posts
    Country: UK

    Default

    I detail JEDIs with WD40. Pulls all kinds of gunk off them.
    RAS .......... Retard Avoidance System.

  10. #7
    Join Date
    Nov 22, 2014
    Location
    USA
    Posts
    33
    Thanks
    20
    Thanked 24 Times in 12 Posts
    Country: United States

    Default

    I love goo-gone for plastics (any of the orange based cleaner). Alcohols and stronger solvents on metals, sometimes on plastics for stubborn caked on crap but be careful or you can start to rub away finishes and actual material.

  11. #8
    Join Date
    Dec 21, 2011
    Posts
    4,125
    Thanks
    2,750
    Thanked 4,907 Times in 1,462 Posts
    Country: Canada

    Default

    I know this is going to sound F'd, but I use gasoline to remove paint/permanent marker from housings that have a grainy texture (like the XTS). It's works good and doesn't screw the finish over.

    Obviously gasoline is an unstable solvent and should not be used indoors or near any source of ignition.

  12. The Following 4 Users Say Thank You to Mars For This Useful Post:

    Avery Johannssenn (Apr 18, 2018),box (Apr 16, 2018),p47r4ck (Apr 21, 2018),triptolemus (Apr 16, 2018)

  13. #9
    Join Date
    Nov 11, 2011
    Location
    /dev/null
    Posts
    233
    Thanks
    7
    Thanked 141 Times in 48 Posts
    Country: United States

    Default

    Quote Originally Posted by Mars View Post
    I know this is going to sound F'd, but I use gasoline to remove paint/permanent marker from housings that have a grainy texture (like the XTS). It's works good and doesn't screw the finish over.

    Obviously gasoline is an unstable solvent and should not be used indoors or near any source of ignition.
    Lighter fluid works great!

  14. #10
    Join Date
    Mar 20, 2016
    Location
    Beside myself
    Posts
    103
    Thanks
    84
    Thanked 170 Times in 72 Posts
    Country: United States

    Default

    Fluid Film. It's a bit pricey, but it has quite a few uses. Including safe to use on and around electrical connections. Not to mention it does a fantastic job of loosening rusty nuts and bolts. If fluid film doesn't loosen them, my next and final option is a torch.
    "My mind is a raging torrent, flooded with rivulets of thought cascading into a waterfall of creative alternatives".

  15. The Following User Says Thank You to clbsquared For This Useful Post:

    Viper1-6 (Apr 16, 2018)

  16. #11
    Join Date
    Dec 13, 2013
    Posts
    33
    Thanks
    4
    Thanked 25 Times in 9 Posts

    Default

    For a variety of adhesives, I have had good luck with putting a piece of electrical tape over it and pulling it back off numerous times. When it loses its effect, I start over with a new piece. Just a thought if you are not sure about chemicals on your polycarbonates.

  17. The Following 2 Users Say Thank You to JeffFireRadio For This Useful Post:

    bellyacher (Apr 16, 2018),code352 (Apr 16, 2018)

  18. #12
    Join Date
    Feb 12, 2014
    Posts
    90
    Thanks
    67
    Thanked 64 Times in 37 Posts
    Country: United States

    Default

    I only use chemicals as a last resort. Goof Off works well for removing "permanent" marker, like when some idiot writes BAD on the front of a radio. Duh.... For sticker adhesive, I suggest you try furniture polish. You know, Pledge or similar spray. The wax in the polish will remove the stickiness and it will start to release with a little elbow grease. That is what I use to remove the sticker residue from the various flash and original dealer labels inside and outside when reconditioning a unit. The polish is also a nice finishing touch to cleaning up a unit. Use sparingly, and remember to remove the wax with rubbing alcohol before trying to afix a new label.

  19. #13
    Join Date
    Feb 04, 2013
    Posts
    98
    Thanks
    4
    Thanked 72 Times in 38 Posts

    Default

    Quote Originally Posted by Mars View Post
    I know this is going to sound F'd, but I use gasoline to remove paint/permanent marker from housings that have a grainy texture (like the XTS). It's works good and doesn't screw the finish over.

    Obviously gasoline is an unstable solvent and should not be used indoors or near any source of ignition.
    I use coleman fuel (white gas) for similar reasons - for what that doesn't work on, isopropyl alcohol does.

  20. #14
    Join Date
    Jul 08, 2013
    Location
    Florida
    Posts
    158
    Thanks
    79
    Thanked 150 Times in 70 Posts
    Country: United States

    Default

    Quote Originally Posted by JeffFireRadio View Post
    For a variety of adhesives, I have had good luck with putting a piece of electrical tape over it and pulling it back off numerous times. When it loses its effect, I start over with a new piece. Just a thought if you are not sure about chemicals on your polycarbonates.
    Another non-chemical method that I have used on sensitive items/areas is a Pentel Hi-polymer Block Eraser - just use some force and the friction will bind the adhesive to the eraser shavings and you can brush them away. Useful when there is a label nearby which solvents will damage.

  21. The Following User Says Thank You to duggerd For This Useful Post:

    Avery Johannssenn (Apr 18, 2018)

  22. #15
    Join Date
    Feb 28, 2012
    Posts
    976
    Thanks
    82
    Thanked 735 Times in 269 Posts
    Country: United States

    Default

    Vegetable oil and elbow grease works well for some adhesives.

  23. #16
    Join Date
    Jul 18, 2013
    Posts
    70
    Thanks
    77
    Thanked 129 Times in 40 Posts

    Default

    Hair dryer or heat gun (on lower setting). Then gently rub with your bare finger.

  24. The Following User Says Thank You to hambone For This Useful Post:

    Mars (Apr 16, 2018)